LiErO2 formation on Er2O3 in static and natural convection lithium

Er₂O₃ is candidate material for insulating coating to prevent the magnetohydrodynamic (MHD) pressure drop in the self-cooled liquid Li blanket system. Although Er₂O₃ is stable material, detailed chemical behavior in liquid Li is not clear. Corrosion behavior of bulk Er₂O₃ in Li is investigated in static and flowing condition in the present study. After these tests, good compatibility of Er₂O₃ was confirmed and slight formation of LiErO₂ was detected by XRD analysis. This chemical behavior did not change in a static and flowing tests, however some of the corrosion product of LiErO₂ was removed easily by the Li flow. Intensity of LiErO₂ peaks in XRD spectrum suggests that the temperature gradient may affect the reaction rate in the natural convection loop. Since corrosion rate of Er₂O₃ is very small, slight change in state will be important information to evaluate lifetime of coating.     

Phase equilibria in the Co-rich Co-Al-W-Ti quaternary system

We determined phase equilibria in the Co-rich Co-Al-W-Ti quaternary system at a temperature range between 900 °C and 1200 °C with a close attention to the thermodynamic stability of the γ′-Co₃(Al, W, Ti) (L1₂) phase, based on micro-structure observation and electron microprobe analysis on bulk alloy samples heat-treated for periods up to 2000 h. In the quaternary system the single phase field of γ′ extends from the Co-Ti binary edge to a composition of Co-5Al-8.5W-8Ti (in at.%) at 900 °C. At the tip of the single phase field, the γ′ phase is in equilibrium with the γ-Co (A1), Co₂AlTi (L2₁) and Co₃W (D0₁₉) phases. The constructed vertical section of phase diagram between Co-9.4Al-9.6W and Co-16.5Ti indicates that there is a narrow composition range around Co-4.5Al-5.4W-7.5Ti in which the γ single phase field exists at high temperatures above 1200 °C and two-phase of γ+γ′ is thermodynamically stable at low temperatures below 1100 °C.     

In-Flight Particle Measurement of Alkali-Free Glass Raw Materials in 12-Phase AC Arc Plasma

In-flight particle measurements of the surface temperature and velocity are important for understanding of melting behavior of glass particles during in-flight melting by multi-phase AC arc plasma. However, the use of optical pyrometry for particle surface temperature has inevitable uncertainties due to non-thermal emissions signals from the plasma plume. This work presents spectroscopic measurements of the non-thermal signals which were found to be caused mainly by the plasma emissions scattered by the particles and the radiation emitted by vapor. After that, the accuracy of thermal radiation measurement was estimated and surface temperature of in-flight glass particle was corrected.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

Ionic liquid enables simple and rapid sample preparation of human culturing cells for scanning electron microscope analysis

Ionic liquid is a kind of salt that stays in a molten state even at room temperature. It does not vaporize at all in vacuum and facilitates electrical conductivity to the sample surfaces for observations with a scanning electron microscope (SEM). In this study, we used an ionic liquid in SEM for the first time to observe fixed human culture cells. The condition for the cell culture using wrapping sheets and SEM settings were varied to elucidate the optimized protocol. Compared to samples prepared by the conventional way, the ionic liquid‐treatment of samples gave SEM images of the cellular ultra structures in more detail, enabling observation of microvilli that made bridges between separated cells. In addition, the ionic liquid treatment is less time consuming as well as less laborious compared with the conventional way that includes dehydration, drying, and conductivity treatments. Totally, we concluded the ionic liquid is a useful reagent for SEM sample preparation. Microsc. Res. Tech., 2011. © 2010 Wiley‐Liss, Inc.     

电子装置内的热移动研究——温度分布及速度分布

在高60cm,宽45cm 的模拟电子装置内,进行装置内热移动研究,得到不同条件下的温度分布及速度分布.在理论解析及数值计算基础上,进行无因次准数关联,得出实验式.实验结果及解析结果基本一致.利用所得实验式对正在运转或有待开发的新的电子装置有关参数进行推算,对于传热设计具有很强的实用性.     

Two-wavelength laser diode interferometer with time-sharing sinusoidal phase modulation

We describe an interferometer system that uses two separate wavelengths to measure step height. The overlapping interference images detected by a CCD camera are easily separated by an ordinary integrating-bucket method and time-sharing sinusoidal phase modulation, in which two laser diodes are alternately modulated with a sinusoidal signal. A phase map is obtained only for the laser diode into which the modulation signal is injected. In this instance, a 1-microm step height was accurately detected.     

Surface modification of an organosilane self-assembled monolayer on silicon substrates using atomic force microscopy: scanning probe electrochemistry toward nanolithography

Organosilane self-assembled monolayers (SAMs) have been applied to resist materials for nanolithography based on scanning probe microscopy. An organosilane SAM was prepared on Si substrates from a precursor, that is octadecyltrimethoxysilane. Using an atomic force microscope with a conductive probe, current was injected from the probe into the SAM-covered Si substrate so that the SAM was locally degraded at the probe-contacting point. Nanoscale patterns drawn on the SAM was clearly imaged by lateral force microscopy. The patterning could be conducted in air while, in vacuum at the order of 10(-6) Torr, no detectable patterns were fabricated. The presence of adsorbed water at the probe/sample junction was confirmed to be crucial for the patterning of the SAM/Si. Its mechanism was, thus, ascribed to electrochemical reactions of both the SAM and Si with adsorbed water.     

Fast incremental learning methods inspired by biological learning behavior

Model-based learning systems such as neural networks usually “forget” learned skills due to incremental learning of new instances. This is because the modification of a parameter interferes with old memories. Therefore, to avoid forgetting, incremental learning processes in these learning systems must include relearning of old instances. The relearning process, however, is time-consuming. We present two types of incremental learning method designed to achieve quick adaptation with low resources. One approach is to use a sleep phase to provide time for learning. The other one involves a “meta-learning module” that acquires learning skills through experience. The system carries out “reactive modification” of parameters not only to memorize new instances, but also to avoid forgetting old memories using a meta-learning module.This work was presented, in part, at the 9th International Symposium on Artificial Life and Robotics, Oita, Japan, January 28–30, 2004     

Low Frequency Susceptibility of High-Density bcc Solid 3He in the Paramagnetic and Nuclear-Ordered States

We have measured the AC magnetic susceptibility and static magnetization of high-density bcc solid ³ He through the nuclear-ordering transition. The susceptibility in the paramagnetic state strongly depends on the frequency of the measuring field. Near the transition temperature a sharp peak in the real part of the AC susceptibility and an abrupt depression in the imaginary part are observed. The transition temperature indicated by the AC susceptibility is higher than that derived from static magnetization. We analyzed the new behavior in the susceptibility in terms of the spin relaxation between the Zeeman system and the exchange system. The relaxation time in the energy flow in the two systems is in the range of milliseconds in the paramagnetic state, and decreases drastically by two orders of magnitude in the ordered state. The relaxation time in the paramagnetic state is interpreted as due to exchange narrowing, while in the ordered state is explained to be the drift time of the spin wave limited by the size of the sample grown in the pores of the sintered silver. The ordering temperature is given as a function of molar volume in the entire range of the bcc phase.